The MLS-9W ultra-low frequency vibration sensor uses the principle of magnetoelectric induction to turn the vibration signal into an electrical signal. Mainly composed of magnetic circuit system, inertial mass, damping spring and other parts. A magnet is rigidly fixed in the sensor housing, and the inertial mass (coil assembly) is suspended from the housing by a spring element.
1. Measuring range: Frequency: 10 ~ 300Hz
Amplitude: 0 to 200um 0 to 500um 0 to 800um (peak to peak)
Intensity: 0 ~ 20mm / s 0 ~ 25mm / s 0 ~ 50mm / s (true RMS)
2. Measurement accuracy: ±0.5, linear error ≤1%FS
3. Measurement method: vertical or horizontal
4. Output signal: current output: 4 ~ 20mA (load ≤ 1KΩ)
5. Ambient temperature: -10 ~ 65 ° C (relative humidity ≤ 85%)
6. Power supply voltage: DC24V (power consumption ≤ 3W)
7. Dimensions: 35 × 75 (mm)
8. Fixed screw hole: M10×1.5×10mm
EN-080/ST-A3B1/vibration speed sensor
Second, the basic principles
The basic principle of the CD-21 series speed sensor is based on an inertial mass (coil assembly) and a housing in which a magnet is fixed. When the inertial mass is suspended from the housing by the elastic element, the sensor housing is fixed to the vibrating body. Above, this
SG-2 Vibration Speed ​​Sensor The vibration speed sensor is usually used to measure the vibration of the bearing and, in a few cases, to measure the vibration of the shaft. When measuring the vibration speed, if the sensor is installed incorrectly or the installation is not strong, the measurement result may be distorted or the sensor may be damaged due to vibration. Therefore, we must carefully choose the installation method of the vibration speed sensor. The vibration sensor is used together with the vibration monitor to achieve continuous long-term monitoring and is suitable for measurement of mechanical vibrations such as steam turbines, fans, pumps, and coal mills. The working principle is based on a primary component that converts mechanical energy into electrical energy. It is solidified by two coils
MLS-9W ultra low frequency vibration sensor HY-3V intelligent vibration monitoring and protection instrument, HY-3S intelligent speed monitoring and protection instrument, HY-3D intelligent travel monitoring and protection instrument, HY-5V intelligent vibration monitoring and protection instrument, HY-5S intelligent speed monitoring and protection Instrument, HY-5D intelligent travel monitoring and protection instrument, HY-6000 rotating machinery monitoring and protection combined device, HY-3500 steam turbine monitoring and protection combined device, HY-8500 vibration monitoring and fault analysis system, HY-VT vibration transmitter, HY- DT stroke transmitter, HY-ST speed transmitter, VS-2 vibration speed sensor (magnetoelectric), VS-2 vibration speed sensor (piezoelectric), RS-1 speed sensor (passive), RS-1 speed Sensor (active), RS-3 reverse speed sensor, CWY-DO point eddy current sensor, TD UT stroke sensor, UHZ-54 level sensor
1. Measuring range: Frequency: 10 ~ 300Hz
Amplitude: 0 to 200um 0 to 500um 0 to 800um (peak to peak)
Intensity: 0 ~ 20mm / s 0 ~ 25mm / s 0 ~ 50mm / s (true RMS)
2. Measurement accuracy: ±0.5, linear error ≤1%FS
3. Measurement method: vertical or horizontal
4. Output signal: current output: 4 ~ 20mA (load ≤ 1KΩ)
5. Ambient temperature: -10 ~ 65 ° C (relative humidity ≤ 85%)
6. Power supply voltage: DC24V (power consumption ≤ 3W)
7. Dimensions: 35 × 75 (mm)
8. Fixed screw hole: M10×1.5×10mm
EN-080/ST-A3B1/vibration speed sensor
Second, the basic principles
The basic principle of the CD-21 series speed sensor is based on an inertial mass (coil assembly) and a housing in which a magnet is fixed. When the inertial mass is suspended from the housing by the elastic element, the sensor housing is fixed to the vibrating body. Above, this
SG-2 Vibration Speed ​​Sensor The vibration speed sensor is usually used to measure the vibration of the bearing and, in a few cases, to measure the vibration of the shaft. When measuring the vibration speed, if the sensor is installed incorrectly or the installation is not strong, the measurement result may be distorted or the sensor may be damaged due to vibration. Therefore, we must carefully choose the installation method of the vibration speed sensor. The vibration sensor is used together with the vibration monitor to achieve continuous long-term monitoring and is suitable for measurement of mechanical vibrations such as steam turbines, fans, pumps, and coal mills. The working principle is based on a primary component that converts mechanical energy into electrical energy. It is solidified by two coils
MLS-9W ultra low frequency vibration sensor HY-3V intelligent vibration monitoring and protection instrument, HY-3S intelligent speed monitoring and protection instrument, HY-3D intelligent travel monitoring and protection instrument, HY-5V intelligent vibration monitoring and protection instrument, HY-5S intelligent speed monitoring and protection Instrument, HY-5D intelligent travel monitoring and protection instrument, HY-6000 rotating machinery monitoring and protection combined device, HY-3500 steam turbine monitoring and protection combined device, HY-8500 vibration monitoring and fault analysis system, HY-VT vibration transmitter, HY- DT stroke transmitter, HY-ST speed transmitter, VS-2 vibration speed sensor (magnetoelectric), VS-2 vibration speed sensor (piezoelectric), RS-1 speed sensor (passive), RS-1 speed Sensor (active), RS-3 reverse speed sensor, CWY-DO point eddy current sensor, TD UT stroke sensor, UHZ-54 level sensor
Gearboxes For Mining And Cement
Gearboxes for Mining Equipment
Chain Conveyor Gearboxes
Conveyor Gearboxes
Elevator Gearboxes
Tunneling Machine Cutting Gearboxes
Vertical & Horizontal Mill Drives
Girth Gear Drives
Belt Gearboxes
Drive Pinions
Planetary Gearbox for Cement,Center Drive Gearboxes,Double Drive Gearboxes for Mills
Huatao Group Limited , https://www.rollerandreducer.com