Model NO.: LWGY
Measuring Media: Liquid or Gas
Measuring Principle: Atomic Physics
Measurement Object: Closed Pipeline
Certification: JIS, DIN, ANS, GB, CE, UL, RoHS, ISO
Medium: Low Viscosity Clean Liquid, Air, Gas
Pressure: Suitable for Very High Pressure
Signal: Pulse, 4~20mA, Hart, RS485
LCD: Yes/No
Ex-Proof: Intrinsic Safety/ Explosion-Proof
Trademark: U-ideal
Transport Package: Wooden Case or Carton
Specification: ISO
Origin: Tianjin, China
HS Code: 90261000
Advantage:Â 1. Low weight, small volumn
2. low cost, low price
3. Good accuracy: 0.5%
4. Is a type of digit flowmeter, also called electronic water flowmeter
5. can be installed vertically or horizontally
6. can be work at high pressure 10MPa
7. connection method: ferrule (snap-on), flange, threaded
1. Operating Principle:
Â
Liquid flows through the turbine housing causing an internal rotor to spin. As the rotor spins, an electrical signal is generated in the pickup coil. This signal is converted into engineering units (liters, cubic meters, gallons etc.) on the local display where is applicable. Optional accessory modules can be used to export the signal to other equipment.
Â
Upon receipt, examine your meter for visible damage. The turbine is a precision measuring instrument and should be handled carefully. Remove the protective plugs and caps for a thorough inspection. If any items are damaged or missing, contact U-IDEAL.
Â
Make sure the turbine flow model meets your specific needs. For your future reference, it might be useful to record this information on nameplate in the manual in case it becomes unreadable on the turbine. Refer to the nameplate for your customized product's specification.
2. Technical DataÂ
ÂMeasuring system Â
| Application range  |
Liquid: water; diesel; gasoline
|
| Measured Value | Â |
| Primary measured value  | Flow Rate |
| Secondary measured value  | Volume flow  |
Design Â
| Features  |  |
| Modular construction  | The measurement system consists of a flow sensor and a signal converter. It is available as compact and as separate version.  |
|
Compact version converter    |
N Type: Pulse output without local display |
| A Type: 4-20mA Output without local display | |
|
B Type: Local Display; Lithium Battery Power; Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â No Output | |
|
C Type: Local Display; 24V DC Power; 4-20mA Output; Â Optional Function: Â
| |
|
Connection   |
Thread: DN4-DN50 |
| Flange: DN15-DN200 (DIN, ANSI, JIS) | |
| Wafer: DN15-DN100 | |
| Measurement Ratio | Standard - 10:1; Optional: 20:1 |
Â
Measuring accuracy Â
| Reference conditions  | Flow conditions similar to EN 29104  |
| Medium: Water  | |
| Electrical conductivity: ≥ 300 μS/cm  | |
| Temperature: +10...+30°C / +50...+86°F  | |
| Inlet section: ≥ 10 DN  | |
| Operating pressure: 1 bar / 14.5 psig  | |
|
Flow Meter Accuracy  |
Standard: 1.0% of rate |
| Optional:Â 0.5% of rate |
Operating conditions Â
| Temperature | Â |
| Process temperature  | T1 Level: -20...+80°C  |
| T2 Level: -20...+120°C  | |
| T3 Level: -20...+150°C  | |
|
Ambient temperature  (all versions)  |
Standard (with aluminum converter housing):  |
| -10…+55°C  | |
| Storage temperature  | -20...+70° |
| Pressure | Â |
|  EN 1092-1  | DN100…DN200: PN 16  |
| DN15…DN80: PN 25 | |
| Other pressures on request  | |
| ASME B16.5 Â | 1/2"...8": 150 lb RF Â |
| Other pressures on request  | |
| JIS Â | 1/2"...8": 10 K Â |
| Other pressures on request  |
Installation conditions Â
|
Installation   |
Take care that flow sensor is always fully filled  |
| For detailed information see chapter "Cautions for Installation" Â | |
|
Flow direction   |
Forward |
| Arrow on flow sensor indicates flow direction. Â | |
| Inlet run  | ≥ 10 DN  |
| Outlet run  | ≥ 5 DN  |
Materials Â
| Sensor housing  | SS304 |  |
| Other materials on request  |  | |
|
Flanges   |
SS304 | Â |
| Other materials on request  |  | |
| Rotor |  |  |
| Standard: 2Cr13 | EN10088-3 Â Â Â Â Â Â 1.4021 | X20Cr13 |
| AISI 420 | Â | |
| BS 420S37 | Â | |
| JIS SUS410J1 | Â | |
| Optional: CD4MCu | DN15…DN80 |  |
| Bearings and Shaft | Tungsten Carbide | Â |
| Converter Housing | Standard: polyurethane coated die-cast aluminum  | |
Process connections
| Flange | Â |
| EN 1092-1 Â | DN15...200 in PN 6...40 Â |
| ASME  | 1/2"…8" in 150 lb RF  |
| JIS  | 1/2"…8" in 10...20K  |
| Design of gasket surface  | RF  |
|  | Other sizes or pressure ratings on request  |
| Thread | DN4…DN50 in PN63 |
Measurable Flow Rate Range: Â
Note: The flow range as blow is for reference only. Consult the factory if you have special requirement. Refer to the nameplate or certificate for actual flow range.
Â
| Nominal Diameter | Standard Flow Range  | Extended Flow Range  | |
| (mm) | (in.) | (m3/h) | (m3/h) Â |
| 4 | 0.15 | 0.04 to 0.25 | 0.04 to 0.4 |
| 6 | 0.25 | 0.1 to 0.6 | 0.06 to 0.6 |
| 10 | 0.4 | 0.2 to 1.2 | 0.15 to 1.5 |
| 15 | 0.5 | 0.6 to 6 | 0.4 to 8 |
| 20 | 0.75 | 0.8 to 8 | 0.45 to 9 |
| 25 | 1 | 1 to 10 | 0.5 to 10 |
| 32 | 1.25 | 1.5 to 15 | 0.8 to 15 |
| 40 | 1.5 | 2 to 20 | 1 to 20 |
| 50 | 2 | 4 to 40 | 2 to 40 |
| 65 | 2.5 | 7 to 70 | 4 to 70 |
| 80 | 3 | 10 to 100 | 5 to 100 |
| 100 | 4 | 20 to 200 | 10 to 200 |
| 125 | 5 | 25 to 250 | 13 to 250 |
| 150 | 6 | 30 to 300 | 15 to 300 |
| 200 | 8 | 80 to 800 | 40 to 800 |
3. Model and SelectionÂ
Model Selection (See Table 1)Â
Table 1: Model Selection Guidance for Liquid Turbine Flowmeter
| Model Suffix Code |  |  |  | Description | ||||||
| LWGY- | Â | Â | Â | Â | Â | Â | Â | Â | Â | |
| Diameter |  |  |  |  |  |  |  |  |
Three Digitals; for example: 010: 10 mm;              015: 15 mm; 080: 80 mm;              100: 100 mm                |
|
| Converter | N | No display; 24V DC; Pulse Output | ||||||||
| A | No display; 24V DC; 4-20mA Output | |||||||||
| B | Local display; Lithium Battery Power; No output | |||||||||
| C |
Local display; 24V DC Power; 4-20mA Output; Â Optional backup power: Lithium Battery |
|||||||||
| C1 |
Local display; 24V DC Power; 4-20mA Output; Modbus RS485 Communication Optional backup power: Lithium Battery |
|||||||||
| H |
Local display; 24V DC Power; Â 4-wire 4-20mA Output & HART Communication |
|||||||||
| Accuracy | ||||||||||
| 05 | 0.5% of Rate | |||||||||
| Flow Range | S | Standard Range: refer to flow range table | ||||||||
| W | Wide Range: refer to flow range table | |||||||||
| Body Material | S | SS304 | ||||||||
| L | SS316 | |||||||||
| Explosion Rating | N | Safety Field without Explosion | ||||||||
| E | ExdIIBT6 | |||||||||
| Pressuring Rating | Â | N | Standard | |||||||
| H(x) | Customized Pressure Rating | |||||||||
| Connection | Â | Â | -DXX |
DXX: D06, D10, D16, D25, D40 D06: DIN PN6; D10: DIN PN10 D16: DIN PN16; D25: DIN PN25 D40: DIN PN40 |
||||||
| -AX |
AX: A1, A3, A6 A1: ANSI 150#; A3: ANSI 300# A6: ANSI 600# |
|||||||||
| -JX |
JX: J1, J2, J4 J1: JIS 10K; J2: JIS 20K; J4: JIS 40K |
|||||||||
| -TH | Thread; DN4…DN50 | |||||||||
| Fluid Temperature |  |  |  | -T1 | -20...+80°C | |||||
| -T2 | -20...+120°C | |||||||||
| -T3 | -20...+150°C | |||||||||
Explanation - Diameter: 50mm; Converter: 24V DC Power Supply, 4-20mA Output, Local Display
Accuracy: 1.0%; Flow range: 4-40 m3/h; Body Material: SS304; No Explosion; Connection: ANSI 150# Flange; Fluid Temperature: -20…+80°C
Automatic Dotted Line Cutting Rewinding Machine
This automatic dotted line cutting and rewinding machine is suitable for non-woven cloth, melt-blown cloth, paper, self-adhesive, Kraft paper, plastic, sponge, film, Cellophane, leather, felt, pearl cotton, PVC and etc.
Dotted Line Rewinding Machine, Auto Dotted Line Making Machine, Point Breaking Cutting and Rewinding Machine, Non woven fabric Dot Line Rewinding Machine, PET Dotted Line Cutting and Rewinding Machine
Suzhou Flying Man Assembly Automation Co., Ltd. , https://www.flyingmans.com